![kodi unable to create gui exiting windows 7 64 bit kodi unable to create gui exiting windows 7 64 bit](http://logo.panel.cx/uploads/install-iptv-on-kodi7.jpg)
The provider will typically need to change the hub or headend setting associated with the card in their system. If the VCTID is something other than 0 but VCT/VCT Rcvd is 0, this indicates that the CableCARD has been configured incorrectly by the cable provider and is not receiving a channel lineup as a result. Contact the provider and ask them to perform a “cold init” or “DAC init” on the card. If the VCTID is 0, this indicates that the cable provider has not yet initialized the CableCARD. Look for the VCTID, and VCT or VCT Rcvd entries. If you are using a Motorola CableCARD, go to the web page for your HDHomeRun device (click on one of the tuner numbers on the Tuners tab in HDHomeRun Setup), then click on CableCARD Menu, then Network Setup. Note that you do not need to send any files, all information is sent automatically once the box is checked.įirst, verify that the second LED from the left on the HDHomeRun is solid green. Make sure to include the 8 digit device ID for your HDHomeRun so our support personnel can review your diagnostic data.
![kodi unable to create gui exiting windows 7 64 bit kodi unable to create gui exiting windows 7 64 bit](https://venturebeat.com/wp-content/uploads/2020/05/iclr-visualization.png)
After the scan finishes, reinsert the card and set the tuner back to CableCARD.On the Digital Cable tab, run a channel scan.On the Tuners tab in HDHomeRun Setup, set one tuner to Digital Cable.After the HDHomeRun finishes initializing, remove the CableCARD.Unplug the power cord from the HDHomeRun, count to ten, and plug it back in.
![kodi unable to create gui exiting windows 7 64 bit kodi unable to create gui exiting windows 7 64 bit](https://usermanual.wiki/Document/Oracle20database20Advanced20Application20Developer20Guide.2117791026-User-Guide-Page-1.png)
![kodi unable to create gui exiting windows 7 64 bit kodi unable to create gui exiting windows 7 64 bit](https://www.videoconverterfactory.com/tips/imgs-self/how-to-install-kodi-on-windows-10/how-to-install-kodi-on-windows-10-04.png)
Check to make sure that signal is present on the cable line you are using. This indicates that either the CableCARD is not initializing correctly, or is not getting an out of band connection.
KODI UNABLE TO CREATE GUI EXITING WINDOWS 7 64 BIT SOFTWARE
If your PC has any VPN software installed, make sure you are not connected to the VPN, and make sure any firewall the VPN may contain is disabled. Any mismatch, no matter how small, can prevent discovery of the device from working. If you are on a wired connection and it is still not discovered, if you have the PC configured to use a static IP address, check to make sure that the subnet mask entered exactly matches what the router is assigning via DHCP. Check the router’s configuration for anything with the word broadcast in it, or anything like wireless partition/isolation/segmentation, and try toggling those options. If the wired connection works but wireless does not, then the most likely cause is your router blocking certain kinds of network traffic. If you are on the main wireless network, please instead try a wired connection. If your PC is using a wireless connection, make sure that you are on the primary network and not a guest network (guest networks typically block access to local devices on the network). If the network LED is solid green, then the HDHomeRun has an address. If the HDHomeRun is directly connected to the network interface on your computer, the interface should be set to a static IP in the .y range (for example, 169.254.1.9) with a subnet mask of 255.255.0.0 If the router has any access control/allowed devices/MAC filtering function, either the HDHomeRun needs to be on the allowed list, or this function should be disabled. If connected to your main network, check to make sure that your router is powered on and has its DHCP server enabled. If the LED is blinking green, this indicates that the device has a network connection, but has not received an IP address via DHCP. Try a different network cable and port on your switch/router. If the LED is blinking red (HDTC-2US) or solid red (other devices), this indicates that the device does not have a network connection. For HDTC-2US, the network LED is at the bottom of the network port. For HDTC-2US, the network LED is the furthest left LED. For HDHR3-US, HDHR3-CC, and HDHR4-2US, the network LED is the furthest left LED. For first/second generation HDHomeRun devices (HDHR-US, HDHR-T1-US, HDHR-EU), the network LED is the leftmost of the ones in the window. Check to make sure that the HDHomeRun has a good network connection, as indicated by the network LED on the device being solid green.